Keysolved
Key Programming18 min read

MG Key Programming: Complete Locksmith Guide (All Models)

Two manufacturers, one badge: five security architectures from Lucas 5AS to Hitag AES, with the procedure and job time for each

Five generations of MG immobiliser control module shown side by side against a dark background, visibly different in age and construction, linked by copper circuit traces

Key Takeaways

  • MG is two makes under one badge: Rover-era cars (ZR, TF, ZT) carry no transponder in the ignition key on the ZR and TF, while every SAIC-built MG from the 2013 MG3 onwards is gated behind a four-digit immobiliser password
  • The Pektron SCU fitted to the ZR from VIN serial 732814 will not talk to any diagnostic tool while armed, so a working fob or the four-digit EKA is needed before you can even connect
  • Only the MG3 can be cloned. The ZS, HS, MG4 and 2024-on ZS use Hitag 3 or Hitag AES, so a working key in the customer's hand saves you nothing
  • The MG3 is the only SAIC MG where the password sits in readable serial EEPROMs (engine ECU 95080, BCM 24C16 or 95160), which makes it the only one with a guaranteed bench route when the socket read fails
  • Smart Pro on ADS2333 is the only confirmed working setup for the 2024-on ZS Hybrid+, and the only tool documented to read the MG3 password over the socket with no working key
  • The signature MG fault is a key that programmes but leaves hands-free start dead. The fix is to erase all keys and relearn the complete set, so bring every key the customer owns

The MG on your driveway at eight o'clock on a Tuesday morning is one of two completely different cars, and the badge will not tell you which. One of them has no transponder in the key at all. The other is gated behind a four-digit immobiliser password that nobody at MG will give you and that you cannot work out from the VIN. That is the first thing to understand about MG key programming: the make is two makes.

Get that call wrong and you have either brought a bench programmer to a job that wanted a fob barcode, or quoted a twenty-minute add-key on a car that needs the engine ECU out. The dividing line is not a model year — it is a change of ownership. Everything built at Longbridge under MG Rover and Nanjing wears Lucas, Pektron or BMW security. Everything built by SAIC from 2013 onwards runs the SAIC body-control architecture, and it is the SAIC cars that are now arriving on your round in volume.

That volume is new. MG took 86,767 UK registrations in the first ten months of 2026, a 4.6 per cent market share and a 24.6 per cent increase on the same period in 2025, with the HS sitting seventh in the national model table on 29,046 cars, according to SMMT registration data. In October alone MG registered 7,837 cars against 5,851 Fords. Whatever your view of the brand, the keys are coming. This guide covers all eleven MGs in the Keysolved MG catalogue, the five security architectures across them, and the honest position on what the aftermarket can and cannot do on the newest ones.

One badge, four suppliers, five systems

Treat MG as a badge rather than a platform and the whole make becomes manageable. There are five distinct security architectures:

  • Lucas 5AS — ZR and early TF to mid-2003. Stand-alone alarm and immobiliser ECU. No transponder.
  • Pektron SCU — ZR and TF from mid-2003. Security Control Unit taking over alarm, immobiliser and body functions. No transponder, barcoded fobs.
  • BMW EWS3D — ZT and ZT-T. The Rover 75 system, which is BMW's EWS3 under another name.
  • SAIC IMMO (Hitag 2) — MG3 2013-2024. BCM-held key table, four-digit password, ID46 transponder.
  • SAIC BCM / PEPS (Hitag 3 and Hitag AES) — ZS, HS, MG4 EV and everything current. Separate keyless control unit, four-digit password read over OBD.

Note what is absent from that list. There is no continuity. A locksmith who has done a hundred ZRs has learnt nothing that helps on a ZS, and the database record for the SAIC-built MG3 says so in terms: no MEMS, no 5AS, no Pektron and no EWS.

The Rover-era cars: the key is not the secret

A Rover-era MG ignition key shown in cross-section with no transponder inside, beside the remote fob whose rolling code actually releases the immobiliser and engine ECU

On the MG ZR and the MG TF the ignition key carries no transponder whatsoever. It turns the barrel and nothing else. The engine is released when the alarm and immobiliser unit receives a valid rolling code from the separate remote fob, and that unit then passes its own EMS code to the engine ECU — MEMS3 on the petrol cars, EDC15M on the diesel.

That single fact changes the job completely. Cutting a key is trivial. Programming a key is meaningless. The work is all in the fob, and which fob depends on a VIN serial rather than a plate.

Lucas 5AS — ZR up to VIN serial 732813, roughly August 2003. A stand-alone unit strapped to the underside of the fascia above the steering column, square black two-button fob, four fobs maximum. No PIN, no EKA and no working fob needed to add one. Programming is a learn mode entered over the K-line, then the LOCK button pressed repeatedly on each fob until the horn sounds. Every fob the customer wants to keep must be in your hand, because the routine erases the rest.

  1. Connect at the socket on the driver's-side face of the centre console, low down by the pedals.
  2. Select the Rover 25 / MG ZR, then the 5AS alarm and immobiliser ECU, then fob programming. Ignition on.
  3. Press LOCK on each fob repeatedly — around eight presses — until the horn sounds.
  4. Repeat for up to four fobs.
  5. Read the EKA in the same session and write it down for the customer.
  6. Test lock, unlock and engine start on every fob.
  7. Time: 20-30 minutes, and the same procedure covers all keys lost because nothing is needed to enter the learn mode.

Pektron SCU — ZR from VIN serial 732814, TF from VIN RD 620459. This is the harder one. The SCU replaced the 5AS and the multi-function unit, took over central locking and body functions, and holds up to ten fobs. On the ZR it hangs on a bulkhead stud behind the glovebox, behind the air-conditioning evaporator housing. Two things make it awkward. First, a new fob needs its 22-character barcode, which means an unbarcoded eBay fob is scrap. Second, the SCU will not talk to any diagnostic tool while it is armed, so you need either a working fob or the four-digit EKA before you connect.

The EKA is entered at the driver's door lock: turn to LOCK and release, then UNLOCK as many times as the first digit, LOCK for the second, UNLOCK for the third, LOCK for the fourth, then unlock the door. The alarm LED lights solid for about a second if it was accepted. Three wrong attempts lock you out for ten minutes. On the ZR the EKA digits can run as high as 15, so count carefully.

  1. Disarm the SCU with a working fob or the EKA.
  2. Connect and select the Rover 25 / MG ZR, then Pektron SCU, then fob programming.
  3. Read and record the current EKA before you touch anything else.
  4. Accept that all existing fobs will be erased. Re-present each one being kept — the horn confirms each.
  5. Enter the new fob's barcode. On the AD100 Pro that is the 20-digit code with the first and last characters omitted; pscan.uk takes the 22-character string and includes a barcode checker.
  6. Test every fob on lock, unlock and start.
  7. Time: 40-60 minutes with a working fob. All keys lost on a Pektron car is rated expert in the database, and on the later YWC001541 SCUs the tool may connect on the EKA alone and still refuse to accept a new fob without a working one. Price it accordingly or decline it.

The ZT is a BMW job in a Rover body. The MG ZT and ZT-T run EWS3D, which is BMW's EWS3 as fitted to the Rover 75, on a separate module under the driver's-side dash behind the bonnet release, held by two security Torx screws. The key carries a Philips Crypto PCF7935 holding the VIN and a rolling variable code. There is no PIN. New keys cannot be coded in over the diagnostic socket at all: it is either a dealer key pre-coded by VIN, or a blank PCF7935 written on the bench from the EWS3D's own data using TMPro2 module 40, which needs a separate reader capable of pulling a locked Motorola MCU. If you have read the BMW key programming guide, you already know this system — it is the same architecture, with ten pre-loaded key slots.

The ZT has one extra trap worth charging for. Remote locking is a completely separate system run by the body control unit, so a key that starts the car will not lock or unlock it until its remote is coded into the BCU using the two barcodes supplied with the key, 16 and 15 characters. Two systems, two jobs, one invoice. Time: 2-3 hours including the bench work.

The SAIC era: a four-digit password and where it lives

A SAIC body control module and keyless entry unit cut away to show the serial EEPROM chips that hold the four-digit immobiliser password, linked by a CAN bus to the diagnostic socket

Every SAIC-built MG gates every key operation behind a short numeric immobiliser password. It is not printed on a card, it is not on the barcode tag that came with the keys — that is a key number for ordering parts — and it cannot be derived from the VIN. What differs between models is where that password lives and whether your tool can read it over the socket.

Model System Transponder Password source AKL skill
MG3 2013-2024 SAIC IMMO PCF7941 / PCF7936, Hitag 2 (ID46) Smart Pro over OBD; otherwise bench from engine ECU 95080 or BCM 24C16 / 95160 Skilled
ZS 2017-2024 flip SAIC BCM PCF7961X, Hitag 3 (ID47) OBD read, or PIN-by-VIN Skilled
ZS 2017-2024 smart SAIC BCM / PEPS NCF29A1X, Hitag 3 (ID47) OBD read from keyless unit Skilled
HS 2018-2024 Proximity PCF7953, Hitag 3 Disputed — see below Expert
HS 2024-2026 SAIC PEPS NCF29A1, Hitag AES OBD read from keyless system unit Skilled
ZS 2024-present SAIC smart key NCF29A1, Hitag AES Smart Pro over OBD, online; or dealer by VIN Skilled
MG4 EV 2022-2025 BCM / PEPS NCF29A1, Hitag AES Not fully confirmed Skilled

Three things follow from that table. The MG3 is the only SAIC car where the password sits in ordinary serial EEPROMs you can read on the bench, which makes it the only one with a guaranteed route when the socket read fails. Everything from the ZS onwards depends on a tool that supports the car. And the Hitag AES cars — the current ZS, the Mk2 HS and the MG4 — cannot be cloned at all, so a working key in the customer's hand saves you nothing.

The chip progression here is worth filing away: Hitag 2 on the MG3, Hitag 3 on the first ZS and HS, Hitag AES on everything from 2024. The transponder chip cross-reference chart sets out what each family means for cloning.

Add key: MG ZS 2017-2024, smart key

The ZS is the SAIC MG you will meet most often, and it comes in two flavours — a bladed flip remote and a push-button proximity car. Both use HU100.

  1. Get the password first. Read it over OBD: Smart Pro with an active internet connection, or on an Autel IM608 Pro II via IMMO > MG > ZS > Smart Key > Control Unit > Keyless System (CAN) > Password Reading. Switch the hazards on to wake the car if the read will not connect.
  2. Use a virgin NCF29A1X Hitag 3 smart key or an Xhorse-generated smart key. A PCF7953X-type MG smart key will not learn to a facelift ZS, and the HS and early ZS EV fobs look identical. Read the customer's key before you order.
  3. Take every other key out of the cabin.
  4. Run Add Key with the new fob in the bottom of the centre-console cup-holder cubby, buttons up — that is the backup induction reader. Ignition ON when the tool asks: press START/STOP twice without the brake.
  5. Test lock, unlock, the door-handle button and push-button start with the fob in your pocket, not in the cubby.
  6. Time: 30-45 minutes including the OBD port hunt. The socket is in the driver's footwell on the right-hand side of the column, above the accelerator, facing down — not left of the column and not in the centre console. If you cannot see it, it has usually popped out of its frame and is hanging loose behind the trim.

All keys lost: MG ZS 2017-2024

  1. Entry is through the driver's door handle, behind a cover you prise off from underneath with a flat blade. Pick or decode the HU100 10-cut.
  2. After a mechanical unlock you have about 15 seconds to get the car into ACC or ON before the alarm triggers. With no programmed key that is not possible, so expect the alarm and connect quickly.
  3. Read the password from the keyless unit over OBD with the hazards on, or have it by VIN before you arrive. A PIN-by-VIN code service runs around £30 and office hours only, and it can come back wrong if the BCM or keyless unit has been replaced.
  4. Run All Keys Lost with a virgin key in the cup-holder cubby and no other keys in the car.
  5. Do not erase keys unless the password is confirmed good and the new key is in your hand. A failed learn after an erase has left a 2018 ZS BCM refusing every key, and the fix is bench work on the BCM or a trip to the dealer.
  6. Cut the emergency blade to the decoded cuts and test everything.
  7. Time: 90 minutes to 2 hours including entry, decoding and cutting.

The MG3 bench route

The MG3 is the one SAIC MG where all keys lost has a guaranteed answer without a tool subscription, because the four-digit password sits in plain form in three different EEPROMs. Advanced Diagnostics claims a socket-based alternative — its ADS2333 MG software release advertises pincode reading and master key creation in all-keys-lost situations — and on the MG3 that is the only tool documented to manage it. If you do not carry Smart Pro, the bench is the route.

The engine ECU 95080 holds the password at rows 0E0 and 100, bytes 12 and 13. The BCM behind the passenger glovebox is a 24C16 on a manual car and a 95160 on the automated-manual, so identify it by the marking on the board rather than by model year.

  1. Decide which module you are opening before you start stripping trim.
  2. Read it with a P001 Programmer, VVDI Prog or the X100 PAD3 EEPROM adapter. Save the full dump before anything else.
  3. While the BCM is open, read and save its 93C56 as well. That is where the remote identities live, and it is your fallback if a replacement remote later refuses to learn over the socket.
  4. Refit the module.
  5. Connect at the socket under the right-hand end of the fascia and run the learn. On OBDSTAR tools the MG3 is filed under ROEWE, not MG — there is an MG brand icon on the same screen and the MG3 is not in it.
  6. Time: 2-3 hours. With a working key present, a 46 clone to an Xhorse Super Chip XT27A66 on a Key Tool Max or VVDI2 finishes a base no-remote MG3 in 20-30 minutes with nothing written to the car at all. The cloning versus programming guide covers when that choice is available.

A locksmith kneeling in a car door aperture at dusk, torch pointed up under the dashboard to find the downward-facing OBD socket, with a diagnostic tablet on the driver's seat

Tool compatibility: an honest read

MG coverage is the weakest part of the aftermarket's SAIC story, and the reason is menu structure rather than capability. Most tools built their MG entries around the 2019-2023 HS and the 2017-2023 ZS. The 2024 model-year cars changed the system underneath while keeping the same model names.

Tier 1 — reads the password itself. Smart Pro on the ADS2333 MG software is the strongest option in the UK trade, and it is the only tool documented to read the MG3 password over the socket with no working key. Advanced Diagnostics has issued at least one further MG update under the same ADS2333 number since, dated September 2026, which its What's New listing records without a model breakdown. It is also the only confirmed working setup in the database for the 2024-on ZS Hybrid+. The honest caveat: on the Mk2 HS the published model list runs only to the 2023 cars, and two releases have gone out since under the same software number without a published list. Put the software on and read the year range off your own screen before you price the job. Category B software, so outright purchase, tokens or a 24-hour token pack.

Tier 2 — reads the password on the cars it knows. The Autel line — IM608 Pro II and IM508S — does the keyless password read over CAN with no XP400 Pro and no G-Box, which makes it a straight OBD job. Early Autel software could not read the password on the bladed ZS and it had to be bought by VIN. The OBDSTAR range — X300 DP Plus, X300 Pro4 and X300 Classic G3 — needs ROEWE/MG software at V42.24 or later for the Mk2 HS, where the entry you want is the TYPE 2 branch and not the older plain MG HS one. If TYPE 2 is not on your screen, the software is behind; do not try the old entry. OBDSTAR is not proven for all keys lost on the ZS, so use a tool with a proven AKL path for that job.

Tier 3 — partial, or password not read. Lonsdor K518 Pro and K518ISE cover the bladed ZS, but the Lonsdor MG and Roewe pincode read does not include the MG3, so budget for a bench recovery. The K518 Pro routine also deletes all keys and then adds, which means every key the customer wants to keep must be with you. Launch X431 IMMO Plus and IMMO Elite ship MG as a named module rather than burying it, which is a genuine point in their favour, but Launch publishes brand-level coverage with no model or year breakdown — verify on the car, never on the phone. The X100 PAD3 is a password-recovery step on the MG3 and the TF, not a complete job, and XTOOL lists Read PIN as unsupported on the Mk1 HS.

The dealer route. MG's own tool is the Bosch VDI III running SAIC's VDS and SIPS applications, covering 2008 to current, accessed through the MG Motor Europe RMI portal. Maverick Diagnostics' MG buyer's guide puts diagnostic and programming access at around €7 per hour and technical information at around €6 per hour, with registration requiring VAT registration, a company registration certificate or a sole-trader letter from an accountant, and proof of trading. MG does not follow a fixed release schedule for VDS updates, and installing one takes 1 to 1.5 hours. The key learn works by generating an application code that is uploaded to SAIC's online system; the authorisation code that comes back unlocks the procedure. Virgin keys only. For a locksmith doing two MGs a month this is hard to justify. For anyone seeing MG volume follow the registration figures, it is becoming the fallback that makes the difference between a job and a tow.

As always, proof of ownership comes first: V5C, customer identification and a record of both before you open a door. All keys lost work on any of these cars sits close enough to vehicle theft that the paperwork is not optional.

Common pitfalls

The key programmes but hands-free start stays dead. This is the signature MG fault and it turns up on the ZS, the Mk1 HS and the Mk2 HS alike. The fob unlocks the car, the tool reports success, and the car will only start with the fob laid on the console coil. The fix is to erase all keys and relearn the complete set in one session rather than adding keys one at a time. Have every key the customer owns with you before you start, because this is not a fault you can diagnose your way out of halfway through.

You picked the MG icon instead of ROEWE. On every OBDSTAR handset the MG3 lives under ROEWE. There is an MG brand icon on the same screen, the MG3 is not in it, and this is the single most common way to waste ten minutes next to a car.

The software is older than the car. MG3 coverage only reached the Advanced Diagnostics MG pack in the autumn 2025 release, so an un-updated Smart Pro shows MG5, GS, ZS and HS and no MG3 at all. OBDSTAR needs V42.24 for the Mk2 HS TYPE 2 entry. Autel's MG menu was written around the 2019-2023 HS. Open your tool and check the year range before you quote, not when you are kneeling in the footwell.

You fumbled the password and the car is now counting. Wrong entries on the SAIC cars are counted and answered with a lockout timer that lengthens with each failure, and on the Mk2 HS it survives a battery disconnect. OBDSTAR has a Remaining Unlock Time function on the MG3 entry — run it before you decide the car is faulty.

You ordered the wrong-looking right fob. The MG HS and early ZS EV smart keys are physically identical to the facelift ZS fob but carry a PCF7953X instead of an NCF29A1X, and the wrong one will not learn. Read the customer's existing key before ordering, or use an Xhorse-generated smart key, which covers it.

You assumed the Mk2 HS socket is where the Mk1's was. It is not. The 2018-2024 car has it further forward above the pedals; the 2024-on car has it above the lower closure panel beneath the column, facing down, invisible from the seat. The muscle memory does not transfer. Every MG port position is in the MG OBD port reference, and the OBD port location guide covers the rest of the fleet.

You went to an MG4 all keys lost without checking. The database is explicit that MG4 EV data is not fully confirmed: whether a PIN is needed for an add key with aftermarket tools is unknown, all keys lost is unconfirmed on OBDSTAR, and one locksmith reported an OBDSTAR could not talk to the car at all with all keys lost and the ignition off. Treat an MG4 AKL as exploratory work and say so when you quote.

Two visually identical MG proximity smart key fobs opened side by side on a bench, their different transponder chips highlighted to show the shells do not reveal which chip is inside

Frequently asked questions

Does an MG key need a transponder?

It depends entirely on which MG. The Rover-era cars — ZR, TF, and the 2001-2005 ZS and ZT — have no transponder in the ignition key on the ZR and TF, and a Philips Crypto PCF7935 on the ZT. Every SAIC-built MG from the 2013 MG3 onwards has a transponder: Hitag 2 on the MG3, Hitag 3 on the first ZS and HS, and Hitag AES on the 2024-on cars.

Can you clone an MG key?

Only the MG3. Its Hitag 2 ID46 transponder clones to an Xhorse Super Chip XT27A66 or equivalent with nothing written to the car, which finishes a base no-remote MG3 outright. The ZS, HS, MG4 and current ZS all use Hitag 3 or Hitag AES and are not cloneable in practice, so a working key does not shorten those jobs.

Where is the immobiliser password on an MG?

On the MG3 it is a four-digit code held in the BCM with a matching copy in the engine ECU, readable on the bench from the engine ECU 95080 or the BCM 24C16 or 95160. On the ZS, HS and later cars it lives in the keyless system or BCM and is read out over OBD by a supported tool. MG does not supply it to owners and it cannot be derived from the VIN.

Which tool is best for MG key programming?

Smart Pro on the ADS2333 MG software, on the evidence available. It is the only tool documented to read the MG3 password over the socket with no working key, and the only confirmed working setup for the 2024-on ZS Hybrid+. Autel and OBDSTAR cover the ZS and HS well when the software is current. No aftermarket tool has fully proven coverage of the MG4 EV.

Is the MG ZS a different car in 2024?

Yes, and it matters. The 2017-2024 ZS is the ZS11 with a Hitag 3 transponder and either a bladed flip remote or a smart key. The 2024-on ZS Hybrid+ is an entirely new car with a Hitag AES smart key, a different immobiliser and, at present, one confirmed aftermarket route. The ZS EV is different again. Confirm which you have before ordering anything.

Do I need SERMI to programme an MG key?

Not for the aftermarket routes described here, which work over the diagnostic socket without manufacturer authorisation. SERMI came into operation in the UK in April 2026 and governs security-related access to manufacturer systems. The MG dealer route via the RMI portal requires its own registration — VAT registration, company documentation and proof of trading — which is a separate requirement from SERMI certification.

Before you go out

MG is now the make most likely to catch out a locksmith who has not looked recently. The badge spans a 2003 hatchback with no transponder and a 2026 hybrid with an AES handshake and no K-line fallback anywhere, and the only thing the two jobs share is the octagon on the bonnet.

Three checks before you leave the unit. Confirm which era you are dealing with — Rover or SAIC — because that decides whether you are bringing fob barcodes or a bench programmer. Open your tool and read the year range off your own screen rather than trusting a menu that was written for the previous generation of the same model name. And read the customer's existing key before ordering a fob, because on this make two visually identical smart keys carry different chips.

Then look the exact car up. Every MG in the Keysolved catalogue carries the transponder, frequency, blade profile, OBD port location, password source and per-tool compatibility notes for that specific generation, with the tool menu paths written out step by step. On a make where the model name tells you almost nothing, that lookup is the job.

Full database access

Look Up the Exact MG

$19/month

Cancel any time · Billed monthly, or save $99 a year paying yearly, in your local currency

Transponder, frequency, blade profile, OBD port location, password source and per-tool menu paths for every MG generation in the database.

VehiclesEvery make
ProceduresStep-by-step
Tool matchingYes
Community tipsYes

No card required to browse — subscribe to unlock full specs and procedures

Frequently Asked Questions

▶Does an MG key need a transponder?
It depends entirely on which MG. The Rover-era cars — ZR, TF, and the 2001-2005 ZS and ZT — have no transponder in the ignition key on the ZR and TF, and a Philips Crypto PCF7935 on the ZT. Every SAIC-built MG from the 2013 MG3 onwards has a transponder: Hitag 2 on the MG3, Hitag 3 on the first ZS and HS, and Hitag AES on the 2024-on cars.
▶Can you clone an MG key?
Only the MG3. Its Hitag 2 ID46 transponder clones to an Xhorse Super Chip XT27A66 or equivalent with nothing written to the car, which finishes a base no-remote MG3 outright. The ZS, HS, MG4 and current ZS all use Hitag 3 or Hitag AES and are not cloneable in practice, so a working key does not shorten those jobs.
▶Where is the immobiliser password on an MG?
On the MG3 it is a four-digit code held in the BCM with a matching copy in the engine ECU, readable on the bench from the engine ECU 95080 or the BCM 24C16 or 95160. On the ZS, HS and later cars it lives in the keyless system or BCM and is read out over OBD by a supported tool. MG does not supply it to owners and it cannot be derived from the VIN.
▶Which tool is best for MG key programming?
Smart Pro on the ADS2333 MG software, on the evidence available. It is the only tool documented to read the MG3 password over the socket with no working key, and the only confirmed working setup for the 2024-on ZS Hybrid+. Autel and OBDSTAR cover the ZS and HS well when the software is current. No aftermarket tool has fully proven coverage of the MG4 EV.
▶Is the MG ZS a different car in 2024?
Yes, and it matters. The 2017-2024 ZS is the ZS11 with a Hitag 3 transponder and either a bladed flip remote or a smart key. The 2024-on ZS Hybrid+ is an entirely new car with a Hitag AES smart key, a different immobiliser and, at present, one confirmed aftermarket route. The ZS EV is different again. Confirm which you have before ordering anything.
▶Do I need SERMI to programme an MG key?
Not for the aftermarket routes described here, which work over the diagnostic socket without manufacturer authorisation. SERMI came into operation in the UK in April 2026 and governs security-related access to manufacturer systems. The MG dealer route via the RMI portal requires its own registration — VAT registration, company documentation and proof of trading — which is a separate requirement from SERMI certification.

Full database access

Stop Guessing on the Driveway

$19/month

Cancel any time · Billed monthly, or save $99 a year paying yearly, in your local currency

Full programming procedures, PIN sources and confirmed tool setups for 11 MGs and more than 60 other makes, checked against tool makers' lists and key suppliers.

VehiclesEvery make
ProceduresStep-by-step
Tool matchingYes
Community tipsYes

No card required to browse — subscribe to unlock full specs and procedures

Sources

  • UK New Car Registration Data — SMMT(2026)— Monthly and year-to-date UK registrations by marque and model. Source for MG's 86,767 registrations and 4.6% share to October 2026, and the HS at seventh in the model table.
  • New Key Programming Software for MG — ADS2333(2026)— Advanced Diagnostics release note for the MG software pack, claiming pincode reading coverage and master key creation in all-keys-lost situations.
  • MG Buyer's Guide — Maverick Diagnostics(2026)— Dealer-tool reference for the Bosch VDI III running SAIC VDS and SIPS: coverage from 2008, hourly access costs, registration requirements and update cadence.
  • MG Motor Europe RMI Portal(2026)— MG's repair and maintenance information portal, the access route for independent repairers to SAIC's online key authorisation system.
mgmg key programmingmg zs keymg hs keymg3 keymg4 evkey-programmingsaiclucas 5aspektron scuews3dhitag 2hitag 3hitag aesid46id47ncf29a1pcf7961pcf7953hu100ne77rall-keys-losteka codeimmobiliser passwordrover 25rover 75