Ford PATS key programming: add key and all keys lost
How Ford PATS works, how to tell which version you have, and the usual add key and all keys lost routes, from 4D keys to Hitag Pro smart keys.
What it is and which cars use it
PATS (Passive Anti-Theft System) is Ford's transponder immobiliser. Ford also calls it SecuriLock. It is "passive" because the driver does nothing to arm it: a transponder in the key head is read every time the ignition goes on, and the car only starts if that key's code is one the immobiliser has stored.
You will meet it on almost every Ford from the late 1990s onwards, on Lincolns, and on some Mazdas built alongside Ford models. What changes across the years is where the key data lives and how you get security access:
- Early cars (to about 1998) used a red master key and slave keys, with up to 16 keys stored.
- From the 1998 model year cars came with two keys, both needed to add a third, and a limit of eight keys.
- Key-start cars through the 2000s and 2010s keep the key data in the PCM, the instrument cluster or the body control module, depending on model.
- Push-button and later key-start cars keep it in the BCM, with a separate keyless module (RFA or KVM) handling the smart key.
The transponder changes too: early Texas fixed-code keys, then the 4D family (4D-60, 4D-63, DST80), and Hitag Pro (ID49) on most UK Fords built from about 2018. Some 2012 to 2018 models carry either DST80 or Hitag Pro inside the same generation, so the year alone won't tell you which blank to order.
How to identify it on the car
On a key-start Ford, look for the transceiver: a coil ring round the ignition barrel, under the steering column shroud. If the key has a plastic head and the car has that ring, it has PATS.
The theft indicator tells you more. It is a small light on the dash, or on some models in the sunload sensor on top of the dash:
- It shows for about three seconds when the ignition goes on, then goes out with a good key.
- It flashes rapidly or stays on when the key isn't recognised, and the car cranks but won't run, or won't crank at all.
- On many cars it flashes every couple of seconds with the ignition off, as a deterrent.
To find where the key data is, connect your tool and read the PATS status. It names the module (PCM, cluster or BCM), the number of keys stored, the minimum the car needs, and whether access is timed or coded. Check this before you quote: it decides the route.
Add key: usual route and tools
With two working keys on an older key-start car. Many Fords with a two-key system let the owner add a key without a tool: each working key in turn, then the new key, inside set time windows. It only works with two programmed keys, it can be switched off in the PCM, and later cars don't support it. Don't rely on it for a quote.
By OBD with a diagnostic or key tool. This is the usual route on everything else:
- Connect and read the PATS status.
- Get security access. On older cars this is a timed wait, usually about 10 minutes with the ignition on. On cars that need coded access, the tool calculates the incode from the outcode, or you enter one from Ford's online service.
- Program the new key, then switch the ignition off and test every key, including the remote.
Most mainstream key tools cover PATS add key by OBD. Check the tool against the exact model and year before you go: coverage on the newest BCMs moves with firmware, and some 2021-on cars are reported to need Ford's own online access when an aftermarket tool can't get security access.
On push-button cars the BCM and the keyless module both need the key, and some procedures finish with a parameter reset. Follow the tool's order exactly.
All keys lost: usual route, and when it goes to the bench
By OBD. Most key-start Fords and many push-button ones can be done by OBD: security access (timed or coded), erase the stored keys, then program the new ones. On many cars the immobiliser won't let the car start until at least two keys are stored, so program two keys on the same visit.
Smart-key cars with the alarm armed. With no key present the alarm stays set and the BCM won't finish all keys lost over OBD. Most tools need a Ford all keys lost bypass cable for these. Flip-key cars without keyless entry don't need it. Have the cable in the van before you quote a smart-key job.
When it goes to the bench. Some cars need the module's data read directly:
- On a range of 2006 to 2010 models (Fiesta, Transit Connect, Mondeo, S-Max) the key data sits in the instrument cluster's processor. If OBD access fails, the cluster's memory can be read, the key data recovered and a key written from it.
- On the latest RH850-based BCMs (for example the 2020-on Transit and many Fiesta Mk8 keyless cars) all keys lost often needs the BCM out and its memory read before the keys can be programmed.
Bench work carries the usual risk of bricking a module. Back up the original data before you write anything, and run the module from a stable, current-limited supply.
What catches people out
Why won't the car start after programming one key on all keys lost?
Many PATS systems need at least two keys stored before the car will start. After an erase, one key isn't enough. Program a second key in the same session, even if the customer only brought one blank.
Do I need every key the customer owns?
Usually yes on all keys lost and on most tool-based procedures that erase the stored keys: any key not present at the time stops working. Ask the customer to bring every key they want to keep.
Why does the security access take so long?
Older cars use a timed wait of about 10 minutes, and the tool can't speed it up. Keep the ignition on and the battery supported for the whole wait, and don't let the tool lose connection, or you start again.
The tool said the key programmed, but the car won't start. Why?
The most common cause is the wrong transponder. A 4D key on a car that expects DST80, or a DST80 key on a Hitag Pro car, can program without an error and still not start the engine. Check the chip on the vehicle record and the key in hand before ordering blanks.
Why does the smart key start the car but not unlock it, or only start from the backup slot?
The key was accepted for starting, but it is the wrong part for the car's keyless system, or the keyless module didn't learn it. Check the part number and frequency against the vehicle record, then redo the procedure for the keyless module.
Every vehicle we hold with this system
No live vehicles are linked to Ford PATS yet. Search by make, model or reg and the vehicle page will show which system it uses.